Bonjour à tous,
Au démarrage de ma Mdk10 official, l'activation de eth0 débouche sur
un échec. Pourtant, la carte semble bien détectée, le pilote bien
identifié, le module correctement monté...Ci-dessous les messages
renvoyés lors du boot, ainsi que la configuration d'eth0 obtenue par
ifconfig. Les messages qui me semblent funestes sont:
eth0: link down
network: activation de l'interface eth0: failed
8139too Fast Ethernet driver 0.9.27
Aug 5 21:28:23 localhost kernel: eth0: RealTek RTL8139 at 0xe1a25800,
00:02:3f:6b:dc:3a, IRQ 19
Aug 5 21:28:23 localhost kernel: ip_tables: (C) 2000-2002 Netfilter
core team
Aug 5 21:28:23 localhost kernel: ip_conntrack version 2.1 (4091
buckets, 32728 max) - 300 bytes per conntrack
Aug 5 21:28:23 localhost kernel: Linux Kernel Card Services
Aug 5 21:28:23 localhost kernel: options: [pci] [cardbus] [pm]
Aug 5 21:28:23 localhost kernel: Yenta: CardBus bridge found at
0000:02:04.0 [103c:006b]
Aug 5 21:28:23 localhost kernel: Yenta: ISA IRQ mask 0x02d8, PCI irq 17
Aug 5 21:28:23 localhost kernel: Socket status: 30000006
Aug 5 21:28:23 localhost kernel: Yenta: CardBus bridge found at
0000:02:04.1 [103c:006b]
Aug 5 21:28:23 localhost kernel: Yenta: ISA IRQ mask 0x02d8, PCI irq 17
Aug 5 21:28:23 localhost kernel: Socket status: 30000006
Aug 5 21:28:23 localhost kernel: cs: IO port probe 0x0c00-0x0cff:
excluding 0xc00-0xc07 0xc10-0xc17 0xc50-0xc57 0xc68-0xc6f 0xcd0-0xcd7
Aug 5 21:28:23 localhost kernel: cs: IO port probe 0x0100-0x04ff:
excluding 0x200-0x20f 0x378-0x37f 0x408-0x40f 0x4d0-0x4d7
Aug 5 21:28:23 localhost kernel: cs: IO port probe 0x0a00-0x0aff: clean.
Aug 5 21:28:23 localhost kernel: inserting floppy driver for 2.6.3-7mdk
Aug 5 21:28:23 localhost kernel: floppy0: no floppy controllers found
Aug 5 21:28:23 localhost kernel: hdc: ATAPI 24X DVD-ROM CD-R/RW CD-MRW
drive, 2048kB Cache, DMA
Aug 5 21:28:23 localhost kernel: Uniform CD-ROM driver Revision: 3.20
Aug 5 21:28:23 localhost kernel: ide-floppy driver 0.99.newide
Aug 5 21:28:23 localhost kernel: drivers/usb/core/usb.c: registered
new driver hiddev
Aug 5 21:28:23 localhost kernel: drivers/usb/core/usb.c: registered
new driver hid
Aug 5 21:28:23 localhost kernel: drivers/usb/input/hid-core.c:
v2.0:USB HID core driver
Aug 5 21:28:23 localhost kernel: NET: Registered protocol family 17
Aug 5 21:28:23 localhost kernel: eth0: link down
network: Application des paramètres réseau succeeded
Aug 5 21:28:23 localhost network: Démarrage de l'interface loopback :
succeeded
Aug 5 21:28:23 localhost ifplugd(eth0)[1400]: ifplugd 0.21b initializing.
Aug 5 21:28:23 localhost ifplugd(eth0)[1400]: Using interface
eth0/00:02:3F:6B:DC:3A with driver <8139too> (version: 0.9.27)
Aug 5 21:28:23 localhost ifplugd(eth0)[1400]: Using detection mode:
SIOCGMIIPHY
Aug 5 21:28:23 localhost ifplugd(eth0)[1400]: Initialization complete,
link beat not detected.
Aug 5 21:28:26 localhost kernel: parport0: Legacy device
Aug 5 21:28:23 localhost network: Activation de l'interface eth0 : failed
Aug 5 21:28:23 localhost internet: Checking internet connections to
start at boot succeeded
eth0 Lien encap:Ethernet HWaddr 00:02:3F:6B:DC:3A
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interruption:19 Adresse de base:0x5800
Merci de votre aide éventuelle, je suis un peu perdue!!
----------------------------------
Informations, désabonnement, règles, obligations sur la liste
Aide-Linux :
http://lists.ze-linux.org/howto_ml.html